Last Updated: October 26, 2026
Quick Summary
To get an electrical remodel quote, write a scope of work listing every circuit, device and fixture, then send the identical briefing pack to three contractors and compare their bids line by line. Most electrical contractors offer a free estimate, but a remodel touching circuits or the panel almost always needs an on-site visit first.
- Photograph the open panel with the main breaker rating visible and include it in the scope pack.
- Send the same scope pack to three contractors so every bid prices the same assumptions.
- An on-site visit is needed when panel capacity is unknown or walls are closed.
- Mark blank rows on a bid as excluded rather than assuming they are included.
- Confirm the contractor's license and bonding through the Washington State Department of Labor & Industries.
Table of Contents
- Start With a Written Electrical Remodel Scope of Work
- Use an Electrical Work Estimate Checklist to Brief Contractors
- Request a Free Estimate and Know When an On-Site Visit Is Needed
- How to Compare Electrician Quotes Line by Line
- Questions to Ask an Electrician Before Hiring
- Red Flags and Contractor Verification Before You Sign
- Request a Quote From S&T Electrical Solutions
- Frequently Asked Questions
Start With a Written Electrical Remodel Scope of Work
The fastest way to get a usable electrical remodel quote is to hand every electrician the same written scope of work. An electrical remodel scope of work is a document that lists every circuit, device, and fixture you want changed, added, or removed during a renovation.
Homeowners who arrive with a written list often get firm, itemized numbers, while those who provide less detail may receive ballpark estimates that can change. The scope is your use.
What Belongs in a Remodel-Specific Scope Checklist
A remodel checklist differs from a repair list because it has to account for walls that are open. Use this as your starting document:
- Room-by-room list of new outlets and receptacles, with wall locations
- Circuits to add, upgrade, or remove, including any 240-volt or 60-amp circuit for a range, dryer, hot tub, or EV charger
- Lighting installation plan: recessed cans, under-cabinet runs, vanity fixtures, switches and dimmers
Room-by-Room Scope Checklist
A room-by-room list is what separates a remodel scope from a repair list. Walk each room with a notepad and record the following. This approach can help produce accurate bids.
Kitchen
- Existing outlets and whether any are GFCI-protected; note locations along counters and the island
- Dedicated circuits for the refrigerator, dishwasher, disposal, microwave, and any double oven or induction cooktop
- Range hood or vent circuit; whether the range is gas or electric and the voltage required
Bathroom
- GFCI receptacle locations and whether each sink gets its own circuit
- Vanity lighting, exhaust fan, and whether the fan is on a timer or humidity sensor
- Heated floor mat or towel warmer circuit, if planned
Bedrooms and Living Areas
- Outlet spacing along each wall and whether any are switched
- Ceiling fan boxes rated for fan weight, and whether a fan-rated box already exists
- Dimmer compatibility with the fixtures you plan to install
Laundry and Utility
- Dryer circuit voltage and amperage; whether the existing receptacle matches the new appliance
- Washer circuit and whether a GFCI is required in the laundry area
- Water heater, furnace, and any sump or well pump circuits
Garage, Exterior, and Additions
- EV charger amperage and whether the panel has capacity for a 40- or 50-amp circuit
- Exterior receptacles, GFCI protection, and in-use covers
- Hot tub or pool equipment circuits and their disconnect requirements
Panel Capacity: The Number That Changes the Bid
Before you send the scope out, photograph the existing panel with the door open and the main breaker rating visible. Note the service size (100-amp, 150-amp, or 200-amp), the number of open breaker spaces, and whether the panel is a brand with known failure issues. A remodel that adds a 50-amp EV circuit and a 30-amp dryer circuit to a 100-amp service with no open spaces will need a panel upgrade, and that line item can change the bid by thousands of dollars.
Why Permits and Code Compliance Belong in the Scope
Permits and inspections are not paperwork that happens after the quote. They change the work. A remodel that adds circuits usually needs a permit, and the inspection schedule affects when the electrician can rough in and when the walls can close.
Ask each contractor to state in writing who pulls the permit and whether the permit fee appears as a line item. Washington requires electrical work to be performed by licensed contractors, and you can verify a license through the Washington State Department of Labor & Industries contractor lookup.
Send the same scope pack to every bidder, including the panel photo and the room-by-room list. When one contractor prices a panel upgrade and another assumes the existing panel is fine, the two bids are not comparable, and the lower number is the one that will grow.
Use an Electrical Work Estimate Checklist to Brief Contractors
An electrical work estimate checklist is the briefing pack you send to every contractor so each one prices the same job. Consistent inputs are what make bids comparable later.
Build one folder, digital or printed, containing:
- The written scope from the section above
- Simple floor plans or photos of each room, marked with outlet and fixture locations
- The existing panel photo with the main breaker rating visible
Send the identical pack to three contractors. The moment one bidder gets extra information the others did not, your comparison falls apart.
Request a Free Estimate and Know When an On-Site Visit Is Needed
Most electrical contractors offer a free estimate, but the format depends on the job. A simple fixture swap can often be priced from photos and a phone call.

Here is how we would sequence the request:
- Call or submit the project details, and say plainly that you are collecting quotes for an electrical remodel.
- Ask what information the contractor needs before the visit.
- Confirm whether the estimate is free and whether it comes in writing.
- Ask who attends the site visit and how long it takes.
- Ask when to expect the written quote.
An on-site visit is necessary when the panel's capacity is unknown, when walls are closed and wiring routes are guesses, or when the scope includes a new 240-volt circuit.
You can discuss electrical changes for your kitchen, bathroom, addition or updated living space with our team if you want the scope reviewed before you send it out.
How to Compare Electrician Quotes Line by Line
Comparing electrician quotes means matching line to line, not totaling the bottom. Two bids can land within a few hundred dollars of each other and still describe completely different jobs.
Set the quotes side by side and check that each one lists:
- Labor hours and the hourly rate, or a stated minimum service fee
- Materials with quantities and brands
- Permit responsibility and fee
If a bid shows only a total, ask for the breakdown before you compare anything.
How to Compare Itemized Electrical Remodel Bids
An itemized remodel bid is comparable only when the line items describe the same work. Build a simple comparison sheet with one column per contractor and one row per scope item, then fill in what each bid actually says. The rows that matter most are the ones where bids diverge:
- Panel work. One bid includes a 200-amp panel upgrade; another assumes the existing panel has capacity. Note the service size each bidder assumed.
- Circuit runs. Count the new home runs each bid includes. A bid that lists "kitchen circuits" without a number is not comparable to one that lists six dedicated circuits.
- Wire and device allowances. If you are supplying fixtures, check whether the bid includes a device allowance and what happens if your fixtures cost more.
When a row is blank on one bid, mark it as excluded rather than assuming it is included. An exclusion is a future change order.
Itemized Bids vs. Lump-Sum Bids
An itemized bid lists labor, materials, permits, and allowances separately. A lump-sum bid gives one number for the whole job. Itemized bids are easier to compare and easier to adjust when you change your mind mid-project.
For a remodel, push for itemized. When the general contractor asks for an added outlet after rough-in, an itemized bid already has a unit price to apply. A lump-sum bid turns that request into a negotiation.
Change Orders, Contingencies, and Remodel Surprises
Every remodel finds something behind a wall. Old wiring spliced outside a box, a panel with no spare capacity, a circuit run through a cabinet that is being removed.
Then set a contingency in your own budget. It is advisable for homeowners to hold back a portion of the electrical budget for surprises, and to insist that no change order gets approved verbally.
A bid that is far below the others usually excludes something: the permit, the panel upgrade, patching, or the inspection coordination. Before you celebrate the low number, find the missing line.
Check each quote against the same line items so you can spot what one bid includes and another leaves out.
| Line item | What to check |
|---|---|
| Labor | Hours and hourly rate, or stated minimum service fee |
| Materials | Quantities and brands listed |
| Permit | Who pulls it and whether the fee is a line item |
| Fixture and device allowances | Included, and what happens if fixtures cost more |
| Demolition and patching | Who patches and paints, or leaves openings |
| Inspection | Who schedules it and who meets the inspector |
| Payment | Payment schedule and deposit amount |
| Temporary power and cleanup | Whether temporary power and debris removal are included |
Questions to Ask an Electrician Before Hiring
The questions to ask an electrician before hiring fall into three groups: licensing, process, and communication. Ask them the same way of every bidder, and write down the answers.
Licensing and insurance
- What is your license number, and are you bonded and insured?
- Who will actually be on site, and are they supervised?
- Will the work be permitted and inspected?
Process
- How do you handle change orders?
- What is your schedule, and how far out are you booking?
- How do you protect floors and finished surfaces during the work?
Communication
- Who is my point of contact, and how do you send updates?
- How quickly do you respond to questions during the project?
- What does the final walkthrough cover?
That last group matters more than most homeowners expect. A contractor who explains the plan and updates you during the job is a different experience from one who hands you a bill at the end.
Red Flags and Contractor Verification Before You Sign
Verification takes ten minutes and protects the whole project. Confirm the contractor's license and bonding status through the Washington State Department of Labor & Industries, and ask for a certificate of insurance showing current general liability coverage.
Then watch for these warning signs:
- A bid with no license number and no permit line
- Pressure to pay a large deposit up front or pay in cash only
- A quote given without ever looking at the panel
Before signing, confirm the contractor actually works in your area. You can check our electrical service area for projects in Wenatchee, East Wenatchee, Cashmere and Leavenworth and contact us to confirm your location.
Request a Quote From S&T Electrical Solutions
Getting an electrical remodel quote comes down to three habits: write the scope, brief every contractor identically, and compare line by line. Do that, and the bids you receive will be numbers you can actually judge.
S&T Electrical Solutions is led by a Washington Master Electrician and licensed as a Washington electrical contractor, license STELEES765B5. If you want the panel cost context before you compare bids, our breakdown of panel upgrade costs explains what drives those line items.
Frequently Asked Questions
Is it free to get a quote from an electrician?
Many contractors offer a free estimate for a defined electrical remodel, while others charge a service-call or minimum service fee that is often credited toward the work if you hire them. Always confirm before booking whether the visit is free or paid, and whether the fee covers a written, itemized quote. S&T Electrical Solutions can walk you through what its estimate covers during the initial conversation.
What information should I provide to get an electrical remodel quote?
Bring a written scope of work: the rooms involved, the fixtures and appliances you plan to add, whether you want a panel upgrade, and any drawings or inspiration photos. Note your home's age, the amperage of the existing electrical panel, and whether walls will already be open. That detail lets the electrician price labor and materials accurately and tell you whether an on-site assessment is needed before the estimate is final.
Should an electrical remodel quote include permits and inspections?
Ask directly. In most jurisdictions, permitted electrical work requires an inspection before the circuit is closed up, and the permit cost may sit inside the bid or appear as a separate line. A quote that lists permits and inspections separately is easier to compare against others. Confirm who pulls the permit, who schedules the inspection, and what happens if the inspector requires corrections.
Can an electrician quote before demolition?
Yes, but treat it as a planning estimate rather than a fixed price. Before walls are open, the electrician works from your scope and a visual walkthrough, so hidden knob-and-tube wiring, undersized circuits, or water damage can change the number. Ask how the contractor handles change orders and what a reasonable contingency looks like so surprises during the remodel do not stall the project.
The real test of a quote is whether it survives contact with an open wall. Ours start with a written scope, a site visit when the job needs one, and itemized pricing you can compare against anyone else's. Tell us about your electrical project or call (509) 630-6604 to request a free estimate, and we will confirm what your remodel actually needs before you commit to a number.


