S&T Electrical Solutions, quality electrical service

Electrical Panel Replacement or Upgrading in Wenatchee, WA

Breaker box replacements and 200 amp panel upgrades for homes in Wenatchee, East Wenatchee, Cashmere and Leavenworth. Licensed, permitted and done to code.

Your electrical panel does not get much attention until something goes wrong. A breaker that will not stay reset. Lights that dim when the dryer kicks on. An old fuse box that came up during a home sale.

Those are the calls we get most often around the Wenatchee Valley, and they usually come down to one question: does the panel need to be replaced, upgraded, or both? S&T Electrical Solutions handles electrical panel replacement and upgrades for homes in Wenatchee, WA and the surrounding towns. Here is a plain-language look at the difference, what to watch for, and why this is one job that belongs with a licensed electrical contractor.

Electrical Panel Replacement

Replacement means swapping a worn-out or unsafe panel for a new one, usually at the same capacity. If your home already has 200 amp service and the panel itself is the problem, a like-for-like replacement may be all you need.

Panels do not last forever. Bus bars corrode. Breakers wear out. Connections loosen after decades of heating up and cooling down, and a loose connection is where heat builds. A new electrical panel box gives every circuit a properly rated breaker and a clean, tight place to land.

On install day, expect the power to be off for most of the day. We pull the old panel, mount the new one, move each circuit over and label everything so you can actually read it. Then we test it before the power comes back on for good.

Inside a newly installed electrical panel with circuits landed on new breakers in Wenatchee, WA
A new panel with the cover off. Every circuit landed on its own breaker, with room left for future circuits.

Signs Your Breaker Box Needs Replacement

Not every old panel is a problem. These are the things worth a closer look:

  • Breakers that trip often, or feel warm to the touch
  • A buzzing or crackling sound coming from the panel
  • Rust, scorch marks, or a burning smell
  • A fuse box instead of breakers
  • A Federal Pacific (Stab-Lok) or Zinsco panel
  • No open spaces left for new circuits

Some of these go beyond safety. Certain insurers hesitate to cover homes with fuse boxes or those older panel brands, and it tends to surface right when you are trying to sell. If your panel is 40 or 50 years old, have it checked even if nothing seems off yet.

One more thing. Flickering lights are not always the panel. Sometimes it is one loose outlet or a tired fixture, which is a much smaller fix. That is why we look first and quote second.

Repair or Replace?

Not every panel problem means a new panel. A broken breaker, a breaker that won’t reset or a loose connection can often be fixed on its own, as long as the panel itself is sound and has the capacity you need. If that sounds more like your situation, see our electrical panel repair page. We will tell you honestly which one you need.

Electrical Panel Upgrading

An upgrade is about capacity. A lot of older homes in Wenatchee were built with 60 or 100 amp service. That was fine for a fridge, a range and some lights. It is not fine for EV chargers, heat pumps, hot tubs and a shop full of tools.

Going from 100 to 200 amps is the upgrade we do most. A 200 amp electrical panel covers most single-family homes with room to grow. Bigger homes, or properties running a shop, a charger and electric heat at the same time, sometimes need a 400 amp panel. We work that out with a load calculation instead of guessing.

An upgrade usually involves more than the panel, too. The meter base and the service wires feeding the house may need to change, and the power has to be shut off and reconnected by the utility. We coordinate that with Chelan County PUD or Douglas County PUD, depending on which side of the river you are on.

Upgraded 200 amp electrical panel with a whole-home surge protector in a Wenatchee, WA home
A 200 amp panel upgrade with a whole-home surge protector, Wenatchee, WA.

How a Panel Replacement or Upgrade Works

From the first look at your panel to the day the power comes back on, here is what to expect.

  1. 01

    Assess the panel and load

    We look at your current panel, its condition and capacity, and run a load calculation based on what you use now and plan to add.

  2. 02

    Permit and utility coordination

    We pull the electrical permit and coordinate the disconnect and reconnect with Chelan County PUD or Douglas County PUD.

  3. 03

    Installation day

    Power goes off, the old panel comes out, and the new one goes in. Every circuit is moved over, tightened and clearly labeled.

  4. 04

    Inspection and power on

    The work is inspected, power is restored, and we test the system and walk you through the new panel before we leave.

Why Hire a Licensed Electrical Contractor for Panel Work

This is not a weekend project. The panel is where utility power enters your home, and the wires feeding it stay live even with the main breaker off.

Washington treats it that way, too. Electrical work generally has to be done by a licensed electrical contractor using certified electricians, and a panel replacement needs a permit and an inspection. There is a narrow exemption for owners working on their own property, but it comes with its own permit, inspection and rules about who does the work.

S&T Electrical Solutions LLC is a licensed Washington electrical contractor (License STELEES765B5). Owner Steven Sabedra holds a Washington Master Electrician license (SABEDSA775QK). You can verify both with Washington L&I. Every panel we replace or upgrade is sized to your actual load, installed to code and inspected before we call it finished. That inspection record helps later, too, when you sell.

Panel Replacement and Upgrades Across the Wenatchee Valley

We are based in Wenatchee and work in East Wenatchee, Cashmere and Leavenworth. Older homes, newer builds and shops on rural lots all need something different. So the first step is always the same. We look at what you have, talk through what you plan to add, and give you a straight answer: replacement, upgrade, or neither. See all of our service areas.

Electrical Panel Replacement and Upgrade FAQs

Is it worth it to upgrade an electrical panel?

If you are adding an EV charger, a hot tub, a heat pump or a shop, or your breakers trip under normal use, usually yes. An upgrade gives the house room for what you run today and what you plan to add. If your current panel is in good shape and has capacity to spare, it may not be needed yet, and we will tell you that.

Can a homeowner replace their own electrical panel?

Washington allows a limited exemption for property owners doing electrical work on their own property, but it still requires a permit, an inspection, and that the owner personally does the work. Panel work is also some of the most dangerous electrical work in a home, since the wires feeding the panel stay live even with the main breaker off. Most homeowners are better served by a licensed electrical contractor.

Will upgrading an electrical panel lower the electric bill?

Not really. A panel distributes power, it does not use it, so a new one will not noticeably change your bill. What it does is make the system safer and let you add equipment, some of which, like a heat pump, can lower energy costs on its own.

Should a 50 year old electrical panel be replaced?

It should at least be inspected. Many panels that age were built for far less load than a modern home uses, and some brands from that era have known problems with breakers that fail to trip. If it is a fuse box, a Federal Pacific Stab-Lok or a Zinsco panel, replacement is the usual recommendation.

Can I upgrade my electrical panel without rewiring my house?

In most cases, yes. The existing circuits are reconnected to the new panel as long as the wiring is in good condition. Rewiring comes up when we find damaged insulation, ungrounded circuits that need attention, or older wiring types that should not be carried forward.

What is the 80% rule for electrical panels?

It comes from the electrical code. A breaker should not carry a continuous load, anything running three hours or more, above 80% of its rating. That is why a 32 amp EV charger goes on a 40 amp circuit. The same idea applies when we size a panel: we want headroom, not a system running near its limit every day.

Can I upgrade my electrical panel from 100 to 200?

Yes, and it is the most common panel upgrade we do. It usually means a new 200 amp panel and often a new meter base and service wires, plus coordination with your utility to disconnect and reconnect power. We handle the permit and inspection.

Is unpermitted electrical work illegal?

In Washington, most electrical work, including panel replacements and upgrades, requires a permit and an inspection through L&I or the local inspecting jurisdiction. Unpermitted work can lead to penalties, problems when you sell the home, and questions from your insurance company if something goes wrong.

Request a project quote

Need a Panel Replacement or Upgrade in Wenatchee?

Send us a photo of your panel and tell us what you plan to add. We will tell you what makes sense for your home.