S&T Electrical Solutions, quality electrical service

Electrical Wiring Installation in Wenatchee, WA

New homes, additions and garages wired to code in Wenatchee, East Wenatchee, Terrace Park, Cashmere and Leavenworth. Permitted, inspected and done right the first time.

Wiring is the part of a house nobody sees once the drywall goes up. That is exactly why it has to be done right.

A rushed install shows up later as breakers that keep tripping, outlets in the wrong places, or a failed inspection that holds up the whole build. S&T Electrical Solutions handles electrical wiring installation in Wenatchee, WA for new homes, additions and garages, with a permit and inspections on every job.

Residential Electrical Wiring Installation in Wenatchee

Most of our residential electrical wiring installation in Wenatchee happens at one of two moments. A new home or addition is framed and ready for rough-in. Or an existing home needs new circuits for a kitchen, a garage, a hot tub or an EV charger.

Both start the same way, with a plan. We look at how you will actually use each room, where furniture and appliances will sit, and what you might add in five years. Then we lay out circuits, outlets, switches and lighting so the wiring fits the house instead of the other way around. Planning ahead now is a lot cheaper than opening finished walls later.

Signs an Existing Home Needs New Wiring or Circuits

Not every house needs a full rewire. Plenty just need a few new circuits in the right places. These are worth a call:

  • Breakers that trip when two appliances run at once
  • Extension cords and power strips doing the work outlets should
  • Two-prong outlets with no ground
  • Lights that flicker or dim when something big turns on
  • A kitchen, garage or bathroom that never got its own circuits

Sometimes the fix is a single dedicated line. Sometimes the panel is the real limit, and an electrical panel upgrade has to come first. We will tell you which one you are dealing with before any wire gets pulled.

Wiring for New Homes, Additions and Garages

On a new build, timing is everything. Rough-in has to land after framing and before insulation, and it has to pass inspection before anyone hangs drywall. We work with your builder’s schedule so the electrical never becomes the reason a job stalls.

Garages get their own attention. A detached garage with a workbench, a freezer or an EV charger needs its own feeder and dedicated circuits, not a couple of outlets borrowed from the house. See more on our new construction electrical and remodel electrical pages.

Electrical rough-in with outlet boxes and wiring run through new framing in a Wenatchee, WA home
Rough-in wiring in a new home, ready for inspection before drywall.

Hot Tub Wiring

A hot tub is one of the most common reasons homeowners need a new circuit. Most need a dedicated 240 volt line from the panel, wire run in outdoor-rated conduit and a GFCI disconnect set within sight of the tub. It is a smaller job than wiring a room, but around water the details matter even more. See our hot tub wiring page for how we handle it, start to finish.

Our Electrical Wiring Installation Process

Every wiring job follows the same path, from the first walkthrough to the final inspection. Here is what that looks like.

  1. 01

    Walkthrough and plan

    We review your plans or walk the space, then map out circuits, outlets, lighting and anything that needs its own dedicated line.

  2. 02

    Permit

    We pull the electrical permit before work starts, so the job is on record with the inspecting jurisdiction from day one.

  3. 03

    Rough-in

    Boxes go on the framing, cable is run and secured, and circuits are brought back to the panel while the walls are still open.

  4. 04

    Rough-in inspection

    An inspector checks the wiring before insulation and drywall cover it up. Nothing gets closed in until it passes.

  5. 05

    Trim-out

    After drywall, we install outlets, switches, fixtures and breakers, and label the panel so you can actually read it.

  6. 06

    Final inspection and walkthrough

    Everything is tested and inspected one last time, then we walk you through the system before we call it finished.

Why Hire a Licensed Electrician for Wiring Installation

Wiring mistakes rarely show up on day one. They show up as heat at a loose connection, an overloaded circuit or a problem the home inspector finds when you go to sell. That is why Washington generally requires electrical work for hire to be done by a licensed electrical contractor using certified electricians, with permits and inspections along the way.

S&T Electrical Solutions LLC is a licensed Washington electrical contractor (License STELEES765B5). Owner Steven Sabedra holds a Washington Master Electrician license (SABEDSA775QK). You can verify both with Washington L&I.

People ask us who does the best electrical wiring installation in Wenatchee. Our honest answer: whoever plans it carefully, pulls the permit, passes inspection the first time and stands behind the work. That is the standard we hold ourselves to on every job.

Electrical Wiring Installation Across the Wenatchee Valley

We are based in Wenatchee and wire homes, additions and garages in East Wenatchee, Terrace Park, Cashmere and Leavenworth. Send us your plans or a few photos of the space and tell us where the project stands. We’ll take it from there. See all of our service areas.

Electrical Wiring Installation FAQs

Do I need a permit for electrical wiring in Washington?

In most cases, yes. New wiring, added circuits and most other electrical work in Washington require an electrical permit and inspection through L&I or the local inspecting jurisdiction. A licensed electrical contractor pulls the permit and schedules the inspections as part of the job.

What is the difference between rough-in and trim-out?

Rough-in is the wiring you never see. Boxes, cable runs and connections to the panel go in while the walls are open, and that work is inspected before anything gets covered. Trim-out happens after drywall and paint, when the outlets, switches, fixtures and covers are installed.

Can you add new wiring to an existing home without tearing out the walls?

Often, yes. Wire can usually be fished through walls and ceilings from the attic, a crawlspace or small access holes. Some patching may still be needed, and older homes can take more planning, but full tear-outs are rarely necessary for adding a few circuits.

How long does it take to wire a new home?

It depends on the size of the home, the plan and the inspection schedule. Rough-in has to fit between framing and insulation, and trim-out happens after drywall. We give you a timeline once we see the plans and know where the build stands.

Can a homeowner do their own electrical wiring in Washington?

Washington has a limited exemption that lets property owners do electrical work on their own property, with a permit, an inspection and rules about who performs the work. Anyone doing electrical work for hire generally has to be a licensed electrical contractor.

Do you wire garages and additions?

Yes. A detached garage usually needs a feeder from the house panel, plus lighting, outlets and any dedicated circuits for tools, a freezer or an EV charger. Additions are wired the same way as new construction, tied into the existing panel if it has the capacity.

Request a project quote

Planning New Wiring in Wenatchee?

Send your plans or photos of the space. We will map out the work and walk you through the next steps.