S&T Electrical Solutions, quality electrical service

Light Fixture Installation in Wenatchee, WA

Ceiling lights, recessed pot lights, pendants and chandeliers for homes in Wenatchee, East Wenatchee, Terrace Park, Cashmere and Leavenworth. Mounted solid and wired safe.

Light Fixture Installation in Wenatchee

New lighting changes a room faster than almost anything else. Paint takes a weekend. A good fixture takes an afternoon.

The catch is what is behind it. The box in the ceiling, the wiring feeding it and the switch on the wall all have to be right for the fixture to be safe. S&T Electrical Solutions handles light fixture installation in Wenatchee, WA, from swapping a dated ceiling light to planning all the lighting in a new kitchen.

Ceiling Light and Recessed Pot Light Installation

Ceiling light installation is the most common call we get. Most are straight swaps, an old dome light out and something better in. Before the new one goes up, we check that the box is secure and rated for the weight, and that the wiring behind it is in good shape. Older homes tend to hide surprises up there.

Recessed lighting is a bigger change. Pot light installation is about layout first. Too few and the room has dark corners. Too many in a straight grid and it looks like an office. We space the downlights around how you use the room, over counters, along walls and away from spots that cause glare. Today’s slim LED recessed lights don’t need a big can or much space above the ceiling, so they work well in remodels too.

Pendants fit in here as well. Over an island they need to hang at the right height and line up with the counter below, not just the ceiling joists above.

Chandelier Installation

Chandeliers are where weight becomes the whole story. A standard fixture box is not meant to carry a heavy chandelier. Large or heavy fixtures need a box and support that are rated for them and tied into the framing.

Then there is height. In an entry or a two-story great room, getting the chandelier up there safely takes the right ladder or scaffolding and at least two sets of hands. We also set the hanging height so it looks right from the floor and clears anyone walking under it, and add a dimmer if you want one. Chandelier installation is one job where “close enough” is not good enough.

Adding Lights Where There Is No Wiring Yet

Want a light where there has never been one? That is doable. We run new wiring from a nearby circuit, add a box and put a switch where it makes sense. In finished rooms we look for a path through the attic or ceiling first to keep patching to a minimum. Bigger lighting plans, like a whole new kitchen layout, fit naturally into remodel electrical work or new electrical wiring installation. Adding a fan instead? See our fan installation page.

How Our Light Fixture Installation Works

Most fixture swaps are done in one visit. New wiring or a full lighting plan takes a little more planning. Either way, here is the path.

  1. 01

    Talk through the fixtures

    Tell us what you are installing and where. We check the fixture weight, the ceiling height and what is in the ceiling now.

  2. 02

    Check the box and circuit

    We confirm the electrical box is rated for the fixture and secured to framing, and that the circuit and switch are in good shape.

  3. 03

    Install and connect

    The fixture is mounted, leveled and wired, with dimmers or new switches added where you want them.

  4. 04

    Test and walk through

    We test every light and switch, set dimmers if needed, and clean up before we leave.

Why Hire a Licensed Electrician to Install Light Fixtures

Swapping a light looks like a small job, and it often is. It is still electrical work. In Washington, anyone installing light fixtures for hire generally needs to be a licensed electrical contractor. A handyman or general contractor registration does not cover it.

S&T Electrical Solutions LLC is a licensed Washington electrical contractor (License STELEES765B5). Owner Steven Sabedra holds a Washington Master Electrician license (SABEDSA775QK). You can verify both with Washington L&I. When we install a fixture, we check what holds it up and what powers it, not just how it looks.

Lighting Installers Across the Wenatchee Valley

We are based in Wenatchee and install lighting in East Wenatchee, Terrace Park, Cashmere and Leavenworth. Send us a photo of the ceiling and a link to the fixture you picked, or just describe the room. We will tell you what it takes. See all of our service areas.

Light Fixture Installation FAQs

Do I need an electrician to install a light fixture?

If you are paying someone to do it, yes. In Washington, electrical work for hire, including replacing a light fixture, generally has to be done by a licensed electrical contractor. Homeowners can do some electrical work on their own property, but a licensed electrician also checks the box, the wiring and the circuit, which is where most problems hide.

Can a handyman change a light fixture?

Not in Washington, unless they are also a licensed electrical contractor. A handyman or general contractor registration does not cover electrical work, even a simple fixture swap. If you are hiring it out, ask for an electrical license number and check it with L&I.

Do I need an electrician to install a ceiling light?

For hire, yes. Ceiling lights also add a few things to check. The box has to be rated for the weight of the fixture and secured to framing, and the fixture has to suit the space, especially in bathrooms, closets and other damp or tight areas.

How do I install a new ceiling light fixture?

The basic steps are to turn off the breaker and confirm the power is off, remove the old fixture, check that the box is secure and rated for the new one, connect the wires and mount the fixture. The hard part is what you find in the ceiling: old wiring, a loose box, or no ground. That is when it is time to call an electrician.

Can a ceiling light be installed where there is no existing wiring?

Yes. We can run new wiring from a nearby circuit, add a box in the ceiling and put in a wall switch. In finished rooms we fish wire through the attic or ceiling where we can to keep drywall repair small.

What light fixtures are outdated?

Common ones are boob lights and flush-mount domes, fluorescent box lights in kitchens, large brass chandeliers and older can lights with yellowed trims. Swapping them for LED fixtures usually changes the look of a room and lowers the power those lights use.

Are 6 inch recessed lights outdated?

Not outdated, just less common in new work. Many homeowners now choose 4 inch or slim LED recessed lights for a cleaner look. Existing 6 inch cans can often take an LED retrofit trim, which is a quick update without cutting the ceiling.

Request a project quote

Ready for New Lighting in Wenatchee?

Send a photo of the ceiling and the fixture you have in mind. We will take it from there.