Electrical Remodeling in Wenatchee, WA
A remodel rarely changes just what you can see. New layouts, appliances and lighting all land on the wiring behind the walls. We help you work out the electrical changes before finishes go in, so nothing has to be opened up twice.

Remodels We Can Help Plan
- 01
Kitchen updates
New appliances, a moved island or added lighting often mean new circuits and relocated outlets.
- 02
Bathroom changes
Fixtures, fans, heating and lighting that need to work with a new layout.
- 03
Additions and finished spaces
A new room, finished basement or converted garage needs outlets, lighting and a supply that fits the space.
- 04
Reworked rooms
Walls removed or added mean outlets and switches that no longer land where you need them.
Electrical Changes That Come With a Remodel
Scope depends on your project and what is already in the walls. Typical conversations cover:
Moving and adding outlets
Placed for the new layout, counters and furniture, not left where the old room had them.
Lighting and switching
New fixtures, recessed lighting or under-cabinet lights, with switches in sensible spots.
New appliance connections
Power for appliances and equipment that the old setup was not built around.
Working with what is there
Reviewing the existing wiring and access so changes fit the home you actually have.
The Electrical Side of Your Remodel
We handle the electrical side of remodeling in Wenatchee. We don't frame walls or hang cabinets. We make sure that when they go up, the outlets, switches, lights and circuits behind them are exactly where the new layout needs them, and that everything passes inspection.
Timing matters more than most people expect. Electrical rough-in has to land after framing and before insulation and drywall. Miss that window and walls get opened twice, so the earlier we hear about your remodel, the smoother it goes for everyone.
Kitchens usually carry the most electrical work: new appliances, an island with outlets, pendants and under-cabinet lights, plus the dedicated circuits code requires. Bathrooms are smaller but fussier, with ground-fault protection, exhaust fans and vanity lighting in a damp space. Additions and finished basements are close to new construction.
Rough-In Wiring While the Walls Are Open
Rough-in is where a remodel is won or lost electrically. With the framing exposed, we set boxes for every outlet, switch and fixture, run new circuits back to the panel and pull out old wiring that no longer serves anything. It is the same work as our electrical wiring installation, fitted around an existing home.
It is also the best chance to fix what was hiding in the walls. Older homes sometimes turn up ungrounded circuits, brittle insulation or connections that were never boxed. We flag anything like that right away, before it gets covered up again.
If the remodel adds a lot of load, the panel may need attention too. An electrical panel upgrade is much easier to plan into a remodel than to add later. For new lighting, see our light fixture installation page.

How We Work Alongside Your Remodel
- 01
Walk through the plan
Tell us what is changing, send photos or a sketch, and flag anything you are unsure about.
- 02
Review the existing setup
We look at what is in place and how reachable it is, since that shapes scope.
- 03
Time it with the other trades
Electrical work needs to land before drywall and finishes. We discuss timing with you and your contractor.
- 04
Finish and confirm
Devices and fixtures are completed and we go over the work with you.
Why Use a Licensed Electrician for Your Remodel
Remodel wiring ends up behind new drywall and finished tile. If something is wrong, fixing it means tearing up the work you just paid for. In Washington, electrical work for hire generally has to be done by a licensed electrical contractor, with a permit and inspections. A general contractor's registration does not cover the electrical, and buyers' inspectors look for permits on remodeled spaces when you sell.
S&T Electrical Solutions LLC is a licensed Washington electrical contractor (License STELEES765B5). Owner Steven Sabedra holds a Washington Master Electrician license (SABEDSA775QK). You can verify both with Washington L&I.
Good to Know
- Opening walls can reveal surprises. We will discuss changes with you as they come up.
- Moving things is often possible, though access to existing wiring affects how much.
- The earlier we hear about the remodel, the easier the timing is.
What Affects the Scope and Cost?
We do not publish flat prices because every property is different. These are the things that move a quote.
- How much of the layout is changing
- Access to existing wiring
- Number of circuits, outlets and fixtures
- New equipment or appliances
- Condition and capacity of the existing setup
- Timing relative to other trades
Remodeling FAQs
Do you do the remodeling itself, or just the electrical?
When should electrical planning begin?
Can outlets and lighting move with the new layout?
What do you need before you can quote?
Could my existing electrical system affect the remodel?

Request a project quote
Tell Us About Your Remodel
Describe the rooms and changes you have in mind and we will follow up about the electrical side.
